Go-eCharger Binding

This Binding controls and reads data from the Go-eCharger (opens new window). It is a mobile wallbox for charging EVs and has an open REST API for reading data and configuration. The API must be activated in the Go-eCharger app.

Supported Things

This binding supports Go-eCharger HOME+ with 7.4kW, 11kW or 22kW. The Go-eCharger HOMEfix with 11kW and 22kW is supported too.

Thing Configuration

The thing has three configuration parameters:

Parameter	Description	Required
ip	The IP-address of your Go-eCharger	yes
apiVersion	The API version to use (1=default or 2)	no
refreshInterval	Interval to read data, default 5 (in seconds)	no

The apiVersion 2 is only available for Go-eCharger with new hardware revision (CM-03).

Channels

Currently available channels are

Channel ID	Item Type	Description	API version
maxCurrent	Number:ElectricCurrent	Maximum current allowed to use for charging	1 (r/w), 2 (r/w)
maxCurrentTemp	Number:ElectricCurrent	Maximum current temporary (not written to EEPROM)	1 (r)
pwmSignal	String	Signal status for PWM signal	1 (r), 2 (r)
error	String	Error code of charger	1 (r), 2 (r)
voltageL1	Number:ElectricPotential	Voltage on L1	1 (r), 2 (r)
voltageL2	Number:ElectricPotential	Voltage on L2	1 (r), 2 (r)
voltageL3	Number:ElectricPotential	Voltage on L3	1 (r), 2 (r)
currentL1	Number:ElectricCurrent	Current on L1	1 (r), 2 (r)
currentL2	Number:ElectricCurrent	Current on L2	1 (r), 2 (r)
currentL3	Number:ElectricCurrent	Current on L3	1 (r), 2 (r)
powerL1	Number:Power	Power on L1	1 (r), 2 (r)
powerL2	Number:Power	Power on L2	1 (r), 2 (r)
powerL3	Number:Power	Power on L2	1 (r), 2 (r)
powerAll	Number:Power	Power over all three phases	1 (r), 2 (r)
phases	Number	Amount of phases currently used for charging	1 (r), 2 (r/w)
sessionChargeEnergyLimit	Number:Energy	Wallbox stops charging after defined value, disable with 0	1 (r/w), 2 (r/w)
sessionChargedEnergy	Number:Energy	Amount of energy that has been charged in this session	1 (r), 2 (r)
totalChargedEnergy	Number:Energy	Amount of energy that has been charged since installation	1 (r), 2 (r)
allowCharging	Switch	If ON charging is allowed	1 (r/w), 2 (r)
cableCurrent	Number:ElectricCurrent	Specifies the max current that can be charged with that cable	1 (r), 2 (r)
temperature	Number:Temperature	Temperature of the curciuit board of the Go-eCharger	1 (r), 2 (r)
temperatureType2Port	Number:Temperature	Temperature of the type 2 port of the Go-eCharger	2 (r)
firmware	String	Firmware Version	1 (r), 2 (r)
accessConfiguration	String	Access configuration, for example OPEN, RFID ...	1 (r/w)
forceState	Number	Force state (Neutral=0, Off=1, On=2)	2 (r/w)

Full Example

demo.things

Thing goecharger:goe:garage [ip="192.168.1.36",refreshInterval=5]

demo.items

Number:ElectricCurrent     GoEChargerMaxCurrent                 "Maximum current"                       {channel="goecharger:goe:garage:maxCurrent"}
Number:ElectricCurrent     GoEChargerMaxCurrentTemp             "Maximum current temporary"             {channel="goecharger:goe:garage:maxCurrentTemp"}
Number                     GoEChargerForceState                 "Force state"                           {channel="goecharger:goe:garage:forceState"}
Number                     GoEChargerPhases                     "Phases"                                {channel="goecharger:goe:garage:phases"}
String                     GoEChargerPwmSignal                  "Pwm signal status"                     {channel="goecharger:goe:garage:pwmSignal"}
String                     GoEChargerError                      "Error code"                            {channel="goecharger:goe:garage:error"}
Number:ElectricPotential   GoEChargerVoltageL1                  "Voltage l1"                            {channel="goecharger:goe:garage:voltageL1"}
Number:ElectricPotential   GoEChargerVoltageL2                  "Voltage l2"                            {channel="goecharger:goe:garage:voltageL2"}
Number:ElectricPotential   GoEChargerVoltageL3                  "Voltage l3"                            {channel="goecharger:goe:garage:voltageL3"}
Number:ElectricCurrent     GoEChargerCurrentL1                  "Current l1"                            {channel="goecharger:goe:garage:currentL1"}
Number:ElectricCurrent     GoEChargerCurrentL2                  "Current l2"                            {channel="goecharger:goe:garage:currentL2"}
Number:ElectricCurrent     GoEChargerCurrentL3                  "Current l3"                            {channel="goecharger:goe:garage:currentL3"}
Number:Power               GoEChargerPowerL1                    "Power l1"                              {channel="goecharger:goe:garage:powerL1"}
Number:Power               GoEChargerPowerL2                    "Power l2"                              {channel="goecharger:goe:garage:powerL2"}
Number:Power               GoEChargerPowerL3                    "Power l3"                              {channel="goecharger:goe:garage:powerL3"}
Number:Power               GoEChargerPowerAll                   "Power over All"                        {channel="goecharger:goe:garage:powerAll"}
Number:Energy              GoEChargerSessionChargeEnergyLimit   "Current session charge energy limit"   {channel="goecharger:goe:garage:sessionChargeEnergyLimit"}
Number:Energy              GoEChargerSessionChargedEnergy       "Current session charged energy"        {channel="goecharger:goe:garage:sessionChargedEnergy"}
Number:Energy              GoEChargerTotalChargedEnergy         "Total charged energy"                  {channel="goecharger:goe:garage:totalChargedEnergy"}
Switch                     GoEChargerAllowCharging              "Allow charging"                        {channel="goecharger:goe:garage:allowCharging"}
Number:ElectricCurrent     GoEChargerCableCurrent               "Cable encoding"                        {channel="goecharger:goe:garage:cableCurrent"}
Number:Temperature         GoEChargerTemperatureType2Port       "Temperature type 2 port"               {channel="goecharger:goe:garage:temperatureType2Port"}
Number:Temperature         GoEChargerTemperatureCircuitBoard    "Temperature circuit board"             {channel="goecharger:goe:garage:temperature"}
String                     GoEChargerFirmware                   "Firmware"                              {channel="goecharger:goe:garage:firmware"}
String                     GoEChargerAccessConfiguration        "Access configuration"                  {channel="goecharger:goe:garage:accessConfiguration"}

Setting charge current of Go-eCharger based on photovoltaik output

You can easily define rules to charge with PV power alone. Here is a simple sample how such a rule could look like:

rule "Set max amps for PV charging"
when
    Item availablePVCurrent received update
then
    logInfo("Amps available: ", receivedCommand.state)
    GoEChargerMaxCurrentTemp.sendCommand(receivedCommand.state)
end

Advanced example:

rule "Set charging limit for go-eCharger"
when
    Time cron "*/10 * * ? * *" // Trigger every 10 seconds
then
    if (GoEChargerExcessCharge.state == ON) {
        var totalPowerOutputInWatt = Total_power_fast.state as DecimalType * 1000
        if (totalPowerOutputInWatt > 0) {
            totalPowerOutputInWatt = 0
        }

        totalPowerOutputInWatt = totalPowerOutputInWatt * -1

        var maxAmp3Phases = (totalPowerOutputInWatt / 3) / 230
        if (maxAmp3Phases > 16.0) {
            maxAmp3Phases = 16.0
        }
        var maxAmp1Phase = totalPowerOutputInWatt / 230;

        if (maxAmp3Phases.intValue >= 6) {
            // set force state to neutral (Neutral=0, Off=1, On=2)
            if (GoEChargerForceState.state != 0) {
                GoEChargerForceState.sendCommand(0);
            }

            // 3 phases
            if ((GoEChargerPhases.state as Number) != 3) {
                GoEChargerPhases.sendCommand(3);
            }

            if ((GoEChargerMaxCurrent.state as Number).intValue != maxAmp3Phases.intValue) {
                GoEChargerMaxCurrent.sendCommand(maxAmp3Phases.intValue)
                // logInfo("eCharger", "Set charging limit 3 Phases: " + maxAmp3Phases.intValue + " A")
            }
        } else {
            if (maxAmp1Phase.intValue >= 6 ) {
                // set force state to neutral (Neutral=0, Off=1, On=2)
                if (GoEChargerForceState.state != 0) {
                    GoEChargerForceState.sendCommand(0);
                }

                // switch to 1 phase -> check if this is useful
                if ((GoEChargerPhases.state as Number) != 1) {
                    GoEChargerPhases.sendCommand(1)
                }

                if ((GoEChargerMaxCurrent.state as Number).intValue != maxAmp1Phase.intValue) {
                    GoEChargerMaxCurrent.sendCommand(maxAmp1Phase.intValue)
                    // logInfo("eCharger", "Set charging limit 1 Phase: " + maxAmp1Phase.intValue + " A")
                }
            } else {
                // switch off
                if (GoEChargerForceState.state != 1) {
                    GoEChargerForceState.sendCommand(1);
                    // logInfo("eCharger", "Switch charging off")
                }
            }
        }
    } else {
        // set force state to neutral (Neutral=0, Off=1, On=2)
        if (GoEChargerForceState.state != 0) {
            GoEChargerForceState.sendCommand(0);
        }

        if ((GoEChargerPhases.state as Number) != 3) {
            GoEChargerPhases.sendCommand(3);
        }

        if ((GoEChargerMaxCurrent.state as Number).intValue != 16) {
            GoEChargerMaxCurrent.sendCommand(16)
        }
    }
end

You can also define more advanced rules if you have multiple cars that charge with a different amount of phases. For example if your car charges on one phase only, you can set maxAmps to output of PV power, if your car charges on two phases you can set maxAmps to pv output / 2, and for 3 phases pv output / 3. In general the calculation would be ´maxAmps = pvOutput / phases`.

Caught a mistake or want to contribute to the documentation? Edit this page on GitHub (opens new window)